Brick chimney stack with new underlay and battens running up to it, family run roofers offering chimney repairs

Family Run Fylde Coast Roofers

Chimney Repairs in Lytham St Annes

Catch small defects early, because a chimney stands in the full force of coastal wind and rain.

  • A free quote and no obligation
  • Our owner started roofing at 17
  • A guarantee on all our work
  • Working across the Fylde coast

Your Free Roof Quote

A few details are all we need to start your free quote.

What you send us is only used to answer your enquiry and prepare a quote. It is not shared for marketing and we hold it for up to 12 months. Find out more in our privacy notice.

  • Quotes Are Free With no obligation

  • Insured Work Public and products liability

  • Family Run Lytham St Annes and the Fylde coast

  • Our Guarantee On every roofing job

Chimney Repairs

Why a chimney wears out faster than the house

Few parts of a house have a harder life than its chimney. The stack stands clear of the roof with all four faces in the weather, while the flue attacks it from inside. Burning fuel leaves sulphates in the masonry, and when they meet moisture they form weak acids that eat into mortar joints and brickwork. Stacks that have not seen a fire for years can still hold those deposits. So the pointing on a chimney often gives out well before the walls of the house below it.

Salt adds to the wear here. Sea spray carries salts onto masonry, and as the surface dries they crystallise in the pores, which stresses the brick faces and joints every time it happens. The weather is uneven too. The strongest winds here nearly always blow from between south and north west, so one side of a stack stays wetter than the other and its joints decay at a different rate. That difference is a common cause of a lean. Tall, slim single flue stacks, often seen on 1930s houses, tend to suffer most.

The treatment varies with how far the decay has gone. Worn joints can be raked out and repointed, using a mortar suited to the brick, because a mix that is too hard can trap moisture in soft, older masonry. Cracked flaunching, the sloped mortar bed holding the pots, can be renewed, and failed flashings replaced in lead. Where brickwork has broken up, the top of the stack may need rebuilding. A pronounced lean should be assessed by a structural engineer. You hear what the stack needs first, and each repair is quoted on its own.

  • Repointing worn mortar joints
  • Renewing cracked flaunching
  • Resetting loose chimney pots
  • Lead flashings around the stack
  • Repairing or rebuilding damaged brickwork
  • Tracing damp on chimney breasts
Brick chimney stack being worked on from scaffold level, a closer view relating to chimney repairs

Signs to Look For

How a failing stack gives itself away

  • A stack that no longer looks straight

    A slight lean is common on old chimneys. A BRE repair guide treats anything over 1mm in every 100mm of height as unsafe, though one conservation architect considers that cautious for historic stacks. If you can see a lean, have it checked, and ask a structural engineer when in doubt.

  • Cracked flaunching or loose pots

    Flaunching takes the weather head on and decays quickly. Once it cracks, water and frost get into the top of the stack and the pots lose their seating. A loose pot high above a path or driveway should be dealt with promptly.

  • Damp on the chimney breast

    Failed flashings, worn pointing and rain entering the flue are the usual reasons for staining indoors. Older stacks often have no damp proof course, so water soaks down through the masonry. Salts left in the plaster can keep drawing moisture from the air, which is why a patch may linger after the repair.

Step by Step

Up the scaffold, then down the stack

  1. Platform and highway licence

    A stack needs a secure working platform, so access is planned first. Scaffold standing on the highway needs a licence from the council, and that has to be in place before it goes up.

  2. Inspect every face

    Joints, brick faces, flaunching, pots and flashings are all checked up close. Any active nest has to be found at this stage, because the law protects it and the work may have to wait.

  3. Report what the stack needs

    The findings are explained to you first. Your quote for the work is free, with no obligation to go ahead. If lifting the pots reveals more damage, that part waits for a conversation with you and its own quote.

  4. From the pots downwards

    Pots are lifted, joints raked out and repointed, and flaunching renewed with a slope to shed water. Lead flashings are then dressed around the base and the roof covering made good.

Our Photos

The Kind of Roofing We Do

A selection of photos taken on our own roofing jobs.

  • Top of a brick chimney under repair, photo from a job covering chimney repairs
  • Terracotta pots on a tall chimney against the sky, part of our chimney repairs service
  • Chimney stack rising over a slate roof with terraced houses beyond, taken on a job involving chimney repairs
  • Underlay and battens fixed around a brick chimney stack, one of our photos of chimney repairs

Browse all our photos

Good to Know

Questions About Chimney Repairs

Should a chimney we no longer use be capped?

Yes, but it should never be sealed solid. A flue needs air moving through it, otherwise damp builds up inside and can show on the chimney breast. The usual answer is a ventilating cap at the top, with a vent into the room where the fireplace has been blocked. Capping also keeps out rain and birds, though the law protects any nest in use, so that has to be left until the birds have gone.

Can we take the stack down instead of repairing it?

Possibly, but check first. Removing a stack may count as permitted development, yet the rules can differ in conservation areas and listed buildings need consent. For the Lytham Avenues conservation area, an Article 4 direction covers alterations to a house and its roof. A shared stack may need a party wall agreement, and taking out chimney breasts always needs building regulations approval. Speak to your council's planning team before anything comes down.

Is it safe to keep lighting a fire with a damaged stack?

Not until it has been checked. If smoke enters the room, stop using the fire. Cracks and failed mortar can let flue gases escape where they should not. Approved Document J says a flue brought back into use should be checked, and a new liner is building work that must be notified unless the installer is registered to self certify it. Once the stack is sound, have the flue swept and smoke tested.

Could a tall stack go back up at its original height?

It often can, though the proportions need checking. Approved Document A says a dense masonry stack with no ties or other restraint should not rise more than 4.5 times its narrowest width above the roof, measured to the top of the pot. Some older slim stacks exceed that, so they may need restraint. Lowering a stack has its own drawbacks, as it can cause downdraughts in a working flue, and it may need consent in a conservation area.

Also Worth a Look

Other Work We Take On

  • Close view of lead flashing stepped up a brick stack, lead work alongside chimney repairs, all from one family firm

    Lead Work

    Flashings, valleys and soakers dressed in sheet lead to suit the job.

  • Old tiled roof lifted back for repair work, roof repairs alongside chimney repairs, all from one family firm

    Roof Repairs

    Slipped tiles, storm damage and stubborn leaks traced and put right.

  • Neat rows of red and brown roof tiles, pitched roofing alongside chimney repairs, all from one family firm

    Pitched Roofing

    Re-roofs and new pitched roofs built for exposed coastal weather.

New red and brown tiles finished up against an older dark roof, free quotes for chimney repairs with no obligation

Talk to Us About Chimney Repairs

Your quote costs nothing and there is no obligation.