Grey sheet roof covering meeting a slope of dark tiles, family run roofers offering single ply roofing

Family Run Fylde Coast Roofers

Single Ply Roofing in Lytham St Annes

One flexible membrane, held down to suit the wind on your site and detailed around every outlet, trim and penetration.

  • A free quote and no obligation
  • Our owner started roofing at 17
  • A guarantee on all our work
  • Working across the Fylde coast

Your Free Roof Quote

A few details are all we need to start your free quote.

What you send us is only used to answer your enquiry and prepare a quote. It is not shared for marketing and we hold it for up to 12 months. Find out more in our privacy notice.

  • Quotes Are Free With no obligation

  • Insured Work Public and products liability

  • Family Run Lytham St Annes and the Fylde coast

  • Our Guarantee On every roofing job

Single Ply Roofing

Single ply explained without the jargon

Single ply is a roof covering made from one layer of flexible polymer sheet, manufactured in a factory and joined on the roof. It comes in three main families, PVC, flexible polyolefin (known as FPO or TPO) and EPDM rubber. PVC and polyolefin sheets are generally welded at the laps, while EPDM is normally jointed with tape and a special primer. Because the material is light and easy to form around details, it suits the refurbishment of existing roofs on houses, shops, warehouses and factories.

Wind uplift decides how the sheet is held down. It is calculated for each building under BS EN 1991-1-4, taking in its location, height, size and roof shape. The result points to a mechanically fastened, adhered or ballasted system, and on a fastened roof it sets the number of fixings in the corners, around the perimeter and across the main area. On the Fylde those figures count for a lot. The prevailing wind is south-westerly, straight off the Irish Sea, and the Met Office records a 79 knot gust at Fleetwood in January 1976.

Salt in the air is a separate worry for the fixings. One fastener maker's design guide classes ground within 2km of the sea as a marine atmosphere and up to 10km as coastal, and it says stainless steel fasteners should be specified in both. Every town from St Annes to Fleetwood falls inside those bands. Blown sand is a smaller but steady nuisance. It builds up at outlets, where it can leave water sitting on the sheet, so keeping them clear is part of looking after a single ply roof here.

  • New single ply roofs
  • Refurbishing worn flat roofs
  • Membrane and seam repairs
  • Domestic, commercial and industrial buildings
  • Perimeter trims, outlets and rooflight details
  • Inspection and routine maintenance
  • Help choosing a suitable membrane
Corner of a grey flat roof finished against neighbouring tiles, a closer view relating to single ply roofing

Signs to Look For

Roofs that suit a single ply membrane

  • Old felt past patching

    A large felt roof with repeated patches, splits and blisters is a common reason to look at single ply. It can replace the old roof, or sometimes go over it, but only once the existing layers have been checked for trapped moisture.

  • Limited spare strength in the structure

    Some older commercial buildings cannot carry much extra weight. A single ply sheet is light, which helps where the frame or deck has little capacity to spare. Added insulation or ballast still has to be checked against what the structure can safely take.

  • A roof full of awkward details

    Rooflights, plant bases, pipes and parapets all interrupt the waterproofing. Single ply forms around them well, and preformed corners and mouldings are made for the difficult spots. Penetrations normally need extra fixings as well, so each one is detailed rather than simply sealed over.

Step by Step

Specifying, laying and testing the membrane

  1. Identify the deck

    First we establish what the deck is made of, then record the falls, outlets and what is already on the building. Strawboard, softboard and chipboard are unsuitable for mechanical fixing, so the deck type can change the whole specification.

  2. Settle the fixing method

    Wind calculations and the deck condition point to a fastened, adhered or ballasted system. Where fasteners are proposed on an existing deck, pull out tests show how well it will hold them.

  3. Lay and join the membrane

    Any vapour control layer and insulation go down first. The sheet is then fixed and its laps joined as the manufacturer specifies, with additional fixings at perimeters and around every penetration.

  4. Probe every seam

    Seams are probed as the work goes on and checked by eye before handover. After that we walk you through the roof and the inspection routine it needs from that point on.

Our Photos

The Kind of Roofing We Do

A selection of photos taken on our own roofing jobs.

  • Long run of grey flat roof covering with a clean edge, photo from a job covering single ply roofing
  • Black sheet covering laid across a low roof beside the scaffold, part of our single ply roofing service
  • Deck boards laid on new joists with a cordless drill close by, taken on a job involving single ply roofing
  • New timber joists partly boarded over on a flat roof, one of our photos of single ply roofing

Browse all our photos

Good to Know

Questions About Single Ply Roofing

Can single ply go straight over my old felt roof?

Sometimes. Overlaying keeps the building weathertight during the work and cuts waste, but the old roof must be dry and the structure strong enough for the extra load. PVC sheets generally cannot sit directly on bitumen without a suitable fleece backing, while polyolefin sheets are generally compatible with aged bitumen. If moisture is trapped or the falls are poor, stripping back is often the better option.

Are single ply roofs up to a coastal gale?

A properly designed system can be. Uplift is calculated for your building and the fixing pattern follows from that result, with more fixings at corners and edges. Perimeter trims must be secured to sound masonry or timber, because damage at the edge can trace back to poor fastening or weak material behind the trim. Those details need the same care as the sheet itself.

How should a single ply roof be looked after?

Have two inspections a year, ideally one in late autumn and one in early spring. The check covers damage, blocked outlets and anything other trades have left behind. Near the coast, look for sand building up around outlets. Silt or algae can be brushed off with a soft bristle brush and rinsed away with water. Avoid chemical cleaners, which may not be compatible with the membrane.

What consents apply when a single ply roof is replaced?

Planning permission is not usually needed for a house if the work leaves its outside appearance largely unchanged. Flats, commercial premises, listed properties and conservation areas can be treated differently, so check with your local planning authority. Building regulations are a separate matter, because insulation normally has to be improved once the renovated area passes half the roof, if the upgrade is feasible. For the details on your building, ask the local building control team.

Also Worth a Look

Other Work We Take On

  • Grey flat roof covering seen along its full length, flat roofing alongside single ply roofing, all from one family firm

    Flat Roofing

    Weathertight flat roofs for extensions, garages and dormers.

  • Single roof window set into grey tiles, roof windows alongside single ply roofing, all from one family firm

    Roof Windows

    Roof windows and skylights fitted to bring daylight into your home.

  • Old tiled roof lifted back for repair work, roof repairs alongside single ply roofing, all from one family firm

    Roof Repairs

    Slipped tiles, storm damage and stubborn leaks traced and put right.

New red and brown tiles finished up against an older dark roof, free quotes for single ply roofing with no obligation

Talk to Us About Single Ply Roofing

Your quote costs nothing and there is no obligation.