Grey flat roof sheet dressed neatly up to a tiled slope, family run roofers offering flat roofing

Family Run Fylde Coast Roofers

Flat Roofing in Lytham St Annes

Good falls, edges that hold in a gale and outlets clear of blown sand are what keep a Fylde flat roof dry.

  • A free quote and no obligation
  • Our owner started roofing at 17
  • A guarantee on all our work
  • Working across the Fylde coast

Your Free Roof Quote

A few details are all we need to start your free quote.

What you send us is only used to answer your enquiry and prepare a quote. It is not shared for marketing and we hold it for up to 12 months. Find out more in our privacy notice.

  • Quotes Are Free With no obligation

  • Insured Work Public and products liability

  • Family Run Lytham St Annes and the Fylde coast

  • Our Guarantee On every roofing job

Flat Roofing

What keeps a flat roof watertight on the Fylde

No flat roof is truly flat. The British Standard for these roofs, BS 6229, calls for a finished fall of at least 1 in 80, and the usual design figure is 1 in 40 so that deflection and building tolerances cannot use it up. If the fall is wrong, rain sits on the surface. Standing water finds any small defect, adds weight to the deck and leaves silt behind. On an older extension or garage, poor falls are often the real fault, and a new covering alone will not cure them.

Sea air and strong gusts add to the strain. Wind pulls hardest at edges and corners, so trims need a secure fixing into sound timber or masonry. Ordinary steel nails and fittings are a poor choice on a roof by the shore, because airborne salt hurries corrosion along. Then come the dunes. Blown sand has long been an issue around Lytham and St Annes, and once it gathers in outlets and gutters, water can back up onto the roof.

We mostly work with three coverings, and also lay single ply membranes. EPDM rubber is usually one sheet cut to suit the roof and bonded to the deck. GRP fibreglass is resin and glass matting laid on site and sealed with a topcoat, which suits awkward shapes. Traditional felt goes down in layers, an underlay first and then a cap sheet on top. Each can work well on the right roof. Once we have seen the deck, the details and how the roof gets used, we will tell you which we would choose and why.

  • EPDM rubber roof coverings
  • GRP fibreglass roof coverings
  • Traditional felt roofing
  • Replacement decking where boards have failed
  • Insulation upgrades when regulations apply
  • Edge trims, upstands and outlets
  • Flat roof repairs and maintenance
Long run of grey flat roof covering with a clean edge, a closer view relating to flat roofing

Signs to Look For

Signs your flat roof needs more than a patch

  • Water still standing after rain

    Puddles that stay long after the rain has stopped point to poor falls, a sagging deck or a blocked outlet. Ponding can shorten the working life of the covering, adds load to the structure and lets more water through if the surface is ever damaged.

  • A soft or springy deck

    A deck that gives underfoot has usually taken on water, and the timber below may be rotting. Moisture trapped in boards causes movement and delamination, so laying a new covering straight over the top only seals the problem in.

  • Splits, blisters or lifting edges

    Cracks in the covering let water work underneath it, and a blister that splits does the same. A trim that has started to lift is more urgent on an exposed roof, because once an edge begins to peel the wind can keep working at it in every gale.

Step by Step

A flat roof, stripped back and built up again

  1. Read the falls and outlets

    Deck, falls, outlets and upstands all get checked, along with the way water leaves the roof. Old felt can contain asbestos where the building was put up or refurbished before 2000, so anything suspect is tested before it is disturbed.

  2. Lift the old covering

    Stripping back shows the true state of the timber beneath. Rotten boards or joists halt the job while we go through the repair with you and give you a separate quote for it.

  3. Correct falls, lay the covering

    Falls are corrected, insulation goes in where it is required and the chosen covering is laid on a clean, dry deck. Resin and adhesives will not bond properly to damp boards, and blown sand has to be swept off first.

  4. Dress upstands, secure trims

    Upstands are taken at least 150mm above the finished surface, trims are fixed down and outlets left clear. At handover we explain the guarantee on our work and the simple upkeep the roof needs.

Our Photos

The Kind of Roofing We Do

A selection of photos taken on our own roofing jobs.

  • Flat roof covering laid tight to a tiled slope, photo from a job covering flat roofing
  • Black sheet covering laid across a low roof beside the scaffold, part of our flat roofing service
  • Deck boards being fitted over new joists with a long level on top, taken on a job involving flat roofing
  • New timber joists partly boarded over on a flat roof, one of our photos of flat roofing

Browse all our photos

Good to Know

Questions About Flat Roofing

Do building regulations apply when a flat roof is replaced?

Usually, yes. Replacing the waterproof membrane counts as renovating the roof under Part L. Renovate more than half of it and the whole roof should normally be brought up to the current insulation standard, where that is technically, functionally and economically feasible. Some smaller repairs fall outside this. Building control at your local council can confirm what applies to your property.

Is a warm roof better than a cold roof?

For most replacements, a warm roof is the safer design. The insulation sits above the deck, so the timber stays close to room temperature and condensation is easier to control. A cold roof has its insulation below the deck and needs a clear ventilated gap, which is hard to achieve against a wall. Converting from cold to warm needs a condensation risk calculation first.

Which covering suits a flat roof close to the sea?

There is no single answer, because the deck, the shape of the roof and how it is used all matter. EPDM, GRP and felt can each do the job if the edges are properly secured and the metal fittings are chosen with salt air in mind. On an exposed roof we pay most attention to the perimeter, where high winds tend to do their damage.

How often should a coastal flat roof be checked?

Aim for twice a year, in early spring and again in late autumn. Sand, leaves and moss should be cleared from outlets and gutters, and any splits, lifting trims or standing water dealt with early. Treat every roof as fragile until someone competent says otherwise. If you would rather not go up there, we can check it for you.

Also Worth a Look

Other Work We Take On

  • Single sheet roof covering beside a dark tiled slope, single ply roofing alongside flat roofing, all from one family firm

    Single Ply Roofing

    New single ply roofs laid, and existing membranes repaired and maintained.

  • Old tiled roof lifted back for repair work, roof repairs alongside flat roofing, all from one family firm

    Roof Repairs

    Slipped tiles, storm damage and stubborn leaks traced and put right.

  • White fascia corner joined to a black gutter, guttering and fascias alongside flat roofing, all from one family firm

    Guttering & Fascias

    New gutters, fascias and soffits to keep rainwater off your walls.

New red and brown tiles finished up against an older dark roof, free quotes for flat roofing with no obligation

Talk to Us About Flat Roofing

Your quote costs nothing and there is no obligation.